OBDEleven – VW Golf MK6 (5K) : quelles sont les possibilités ? (Codages, Lecture de code défaut, fonction entretien …)

Explorez Votre VW Golf MK6 avec OBDEleven : personnalisation, entretien, lecture des codes défaut, suivi en temps réel .. L’art de la personnalisation atteint de nouveaux sommets avec OBDEleven sur la VW GOLF MK6 !

Dans ce guide, je vous regroupe toutes les possibilités pour personnaliser votre Golf 6 : Codage et codage long, Exemple de codage VAGCOM : activation des feux US, modification des clignotants de confort, fermeture automatique des vitres en cas de pluie …

Véhicule concerné dans cet article

Marque : Volkswagen
Model : Golf
Année : 2008-2013
Châssis : 5K

Quelles sont les possibilités d’activation sur VW Golf MK6 2008-2013 avec OBDEleven ?

Nbre de codages / possibilités : 200

Nom du Codage	Descriptif
Start/Stop System Deactivation	Start/Stop system - automatically shuts down and restarts the engine to reduce the amount of time the engine spends idling, thereby reducing fuel consumption and emissions ⚙ Fonctions You can temporarily disable the Start/Stop system by pressing Start/Stop button, but this stays active only until you turn off the engine. This function will permanently disable Start/Stop system 📖 Prérequis The vehicle must have a Start/Stop system installed
Comfort Windows	Open/Close the windows via remote key by holding Lock/Unlock buttons or holding the key rotated for some time in a lock of the door handle 📖 Prérequis The electric windows must be calibrated
Refuel Quantity in Dashboard	This additional view shows how much fuel is needed to fully fill up your tank at the given moment ⚙ Fonctions Enable or disable refuel quantity view ⚠ Attention Works only for GTI, GTD and R
Rear Wiper With Front Wiper (Interval)	?? Functions Enable automatic rear window wiping when front wipers are set to "interval" position
Rear Wiper With Front Wiper (Permanent)	?? Functions Enable automatic rear window wiping when front wipers are set to "permanent" position
Footwell Light Dimming w/Door Open	?? Functions Adjust the footwell light behaviour when door is open - footwell lights off, or lit at brightness 10 - 100% 📖 Prérequis Footwell lights must be installed
Permanent Running Lights	Permanent running lights keep your car visible to other drivers during daytime even when the headlights are switched off ⚙ Fonctions Enable or disable permanent running lights via Low Beam
Consumption Display Correction	If the fuel consumption displayed in the MFD (multi function display) differs compared to real measured fuel consumption, it is possible to adjust the value, so that the correct fuel consumption is displayed. ⚙ Fonctions Adjust the indicated fuel consumption from 85% to 115% 📖 Prérequis Vehicle must have an instrument cluster with multi function display.
Automatic Rain Closing // Fermeture automatique en cas de pluie	Cette fonction ferme automatiquement les vitres et le toit ouvrant de votre véhicule lorsque le capteur de pluie détecte de la pluie.. ⚙ Fonctions OFF - fonction désactivée ON - fonction activée 📖 Prérequis Le détecteur de pluie doit être installé et actif ⚠ Attention Le calibrage des fenêtre doit avoir été effectué (tout comme la fermture en une seule impulsion sur les boutons des feêntres du véhicule en cas de coupure de batterie)
Needle sweep V2	Gauge Test/Needle Sweep - sweep the gauge needles through their full range automatically on your dashboard when you turn the ignition on. ?? FUNCTION Turn ON or OFF needle sweep on your vehicle. ?? ATTENTION V2 - is for the reason is the needle sweep is not supported.
Tail Light Dimming	Select the tail light dimming changing the voltage. ⚙ Fonctions Inactive - Direct battery voltage 12.3V - 7% 12.4V - 14% 12.5V - 21% 12.6V - 28% 12.7V - 35% 12.8V - 42% 12.9V - 49% 13.0V - 56% 13.1V - 63% 13.2V - 70% 13.3V - 77% 13.4V - 84% 13.5V - 91% 13.6V - 100%
Headlight Dimming	Select the headlight dimming changing voltage. ⚙ Fonctions Inactive - Direct battery voltage 12.3V - 7% 12.4V - 14% 12.5V - 21% 12.6V - 28% 12.7V - 35% 12.8V - 42% 12.9V - 49% 13.0V - 56% 13.1V - 63% 13.2V - 70% 13.3V - 77% 13.4V - 84% 13.5V - 91% 13.6V - 100%
Delay Alarm Activation	Select how to start the anti-theft alarm delay. When the door is opened/when the door is unclocked. ⚙ Fonctions Door Opened Door is Unlocked 📖 Prérequis The vehicle must have an original anti-theft system installed.
Lock/Unlock Confirmation Turn Signals	Return message with turn signals when locking/unlocking via remote control. The function is useful to know do the vehicle was been locked or unlocked. ?? FUNCTION Turn OFF or ON lock/unlock confirmation with turn signals. ? REQUIREMENTS Vehicle must have an original alarm security signal.
Lock/Unlock- Horn Confirmation	This application will activate horn lock and unlock confirmation. Having this activated on your vehicle will allow you to walk away from your vehicle knowing that its secure. ?? FUNCTION Turn ON or OFF horn confirmation of locking and unlocking. ? REQUIREMENTS Vehicle must have OEM security system installed.
Comfort Blinking	With the comfort blinker function, the indicator stalk needs to be touched only once for the direction indicators to flash three(by default) times. ?? FUNCTION Turn OFF or ON the comfort blinking function in the vehicle.
Central Locking	Power door locks (also known as electric door locks or central locking) allow the driver or front passenger to simultaneously lock or unlock all the doors of an automobile or truck, by pressing a button or flipping a switch. This one-click application allows to unlock just the driver door and with the second press of the unlock button on the key fob other doors will be unlocked. ?? FUNCTION Set Central Locking to unlock just the driver door or all doors with a press of unlock button on the key fob.
Comfort Operation for Driver's Window	Comfort operation will work only for the driver's window. ?? FUNCTION Turn OFF or ON the comfort operation only for the driver's window. After turning the function ON, hold the unlock button on the remote, and the driver's window will open. Vice versa with the lock button. ? REQUIREMENTS Windows must be calibrated.
Windows/Sunroof with Ignition	Windows/Sunroof power can be swtiched OFF after the Ignition or leaved ON. Adjust the setting of windows/sunroof power after the ignition is switched OFF. ?? FUNCTION Turn OFF or ON windows/sunroof power after the ignition is swtiched OFF.
Enable Rear Wiper with Reverse Gear	If the front windshield wipers are ON, the rear window wiper will turn ON automatically when the vehicle is shifted into R (Reverse) gear ⚙ Fonctions Enable or disable the rear wiper feature in reverse gear 📖 Prérequis Front windshield wipers must be turned ON ✅ Procédure After app activation in the dashboard menu go to Settings -> Convenience -> Factory setting -> OK
Brake Lights with Ignition	After pressing the brake pedal the brake lights start to light. Adjust the settings of brake lights to work or not to work after the ignition is OFF. ?? FUNCTION Turn OFF or ON the function for brake lights to work after the ignition is switched OFF.
Visual Confirmation for Comfort Operation	Comfort Operation - Open/Close the windows from the remote key by holding Lock/Unlock buttons (Lock - will close the windows/Unlock - will open the windows) The visual confirmation will let to know that the comfort operation has been successfully ended. ?? FUNCTION Turn ON or OFF visual confirmation for comfort operation. ? REQUIREMENTS The comfort operation must be turned ON.
Comfort Opening Type for Sunroof	The sunroof have two types for comfort operation. ?? FUNCTION Select to Open or Lift the sunroof in comfort operation. ? REQUIREMENTS The comfort operation for sunroof must be turned ON.
Comfort Operation for Sunroof	Comfort opening and closing for sunroof holding the lock/unlock button on remote. ?? FUNCTION Turn OFF or ON the comfort operation for sunroof. Hold the unlock button on remote key to open the sunroof or hold the lock button to close it.
Comfort Windows Operation in Door Lock	Open or close windows and sunroof using door lock. ?? FUNCTION Turn OFF or ON the comfort windows in the door lock. After turning ON, hold the key in the door lock to unlock position to open or in lock position to close. ? REQUIREMENTS Windows must be calibrated.
Auto Lock Rear Lid	The rear lid auto locks when the vehicle starts moving and accessing speed of 15 km/h. ?? FUNCTION Turn OFF or ON the auto lock of rear lid.
Headlights for Traveling to RHD/LHD	Setting allows to switch the headlights between Left-Hand-Driving (LHD) and Right-Hand-Driving (RHD) when traveling into a country which is opposite to what the vehicle was originally made for. ?? FUNCTION Turn OFF or ON the tourist mode for traveling to RHD/LHD countries. If the vehicle was originaly made for left hand driving, turning the application ON will set the headlights for right hand drive and vice versa.
Rear Fog OFF when High Beams ON	?? FUNCTION Turn OFF or ON the function to turn OFF the rear fog light when the high beams are ON. OFF - the high beams will be active when the rear fog is turned ON. ON - the high beams will be inactive when the rear fog is turned ON.
DRLs Inactive when Turn Signals Active	Daytime running lights (DRLs) inactive with turn signals active. ?? FUNCTION Turn OFF or ON the function to DRLs be inactive when the turn signal is active. ? REQUIREMENTS The vehicle must have daytime running lights be activated.
CH/LH Lights via Low Beams/Fog Lights	CH - Coming Home makes it easier to see your surroundings when you get out of your car in the dark. LH - Leaving Home works by turning on the lights when you use the key fob to unlock your doors. ⚙ Fonctions Change the CH/LH lights to work via low beams or the fog lights. ? REQUIREMENTS CH/LH Lights function must be turned ON.
CH Lights Timer Functionality	CH - Coming Home makes it easier to see your surroundings when you get out of your car in the dark. ?? FUNCTION Change when the coming home lights timer will start to calculate. When Ignition OFF - after the ignition will be switched OFF, CH lights will start to work for the set time. When Door Open - after the doors will be opened, CH lights will start to work for the set time. ? REQUIREMENTS CH Lights function must be turned ON.
CH Lights Mode	CH - Coming Home makes it easier to see your surroundings when you get out of your car in the dark. ?? FUNCTION Switch CH Lights to Auto or Manual. Auto - when it is dark outside. Manual - flash high beams when the ignition is off to activate. ? REQUIREMENTS For Auto CH Lights the auto headlights are required. CH Lights function must be turned ON.
CH/LH Lights	CH - Coming Home makes it easier to see your surroundings when you get out of your car in the dark. LH - Leaving Home works by turning on the lights when you use the key fob to unlock your doors. ⚙ Fonctions Turn ON or OFF CH/LH Lights function. ? REQUIREMENTS The vehicle must have automatic headlights.
Instrument Cluster Language	?? FUNCTION Change the language of the instrument cluster.
Multi Function Indicator	?? FUNCTION Turn OFF or ON the multi function indicator. ? REQUIREMENTS Vehicle must have multi function indicator.
ESC deactivation V2	ESC - Electronic Stability Control (a computerized technology that improves a vehicle's stability by detecting and reducing loss of traction (skidding)). ASR - A traction control system (TCS), also known as ASR Usable when ESC deactivation app doesn't work. ?? FUNCTION Turn OFF the ASR. Turn OFF the ASR and ESC. ?? IN CAR PROCEDURES To disable the ESC press and hold the ESC button for 5 seconds. ?? ATTENTION Not working with ABS units 1K0907379AH/1K0907379AJ/1K0907379BH/1K0907379BJ/1K0907379BK/1K0907379BL ECS function is for security purpose and helps to avoid accidents. We do not encourage or recommend to turn OFF this function.
Auto Folding Mirrors	Auto Folding Mirrors - side mirrors may be manually or electrically folded in, to protect them when the car is parked or being washed in an automated car wash. ⚙ Fonctions Unfold with ignition - fold mirrors after locking via key fob with a long click and unfold after ignition is turned on. Unfold with door - fold mirrors after locking via key fob with long click and unfold after driver door is opened. OFF - Turn OFF Auto folding mirrors. 📖 Pré Requis Folding mirrors must be installed. ?? IN-CAR PROCEDURE After app activation function must be enabled on car multimedia 'MIRRORS AND WIPERS' menu. ?? ATTENTION Only for UDS control modules. Please check this in the doors control modules Information section.
MirrorLink in motion 2	"MirrorLink in Motion - Allows the PASSENGER to watch videos on multimedia while vehicle is moving by removing the restriction of MirrorLink function while the vehicle is moving. This app is usable if you have retrofitted MIB II unit! Use this app if "MirrorLink in motion 1" is NOT SUPPORTED. ?? FUNCTIONS ON - MirrorLink is available while driving. OFF - MirrorLink not available while driving. ? REQUIREMENTS Use this app only if you are able to use the MirrorLink in still standing and it locks when you start driving! ?? IN-CAR PROCEDURE 1. Turn the ignition ON. Do not start the engine! 2. Let Multimedia to fully start (it takes around 3 minutes) before using this application. 3. After MirrorLink activation, multimedia must be restarted if not restarted automatically. To restart multimedia press and hold power on button for 20s. ?? ATTENTION This functions is disabled for security reasons and helps avoid accidents. It can be very dangerous if the driver is distracted with the video, wherefore we do not recommend nor encourage this function to be activated. Laws in some countries do not allow this function to be enabled. Do this at your own risk! We are not responsible for any loss or damage.
MirrorLink in motion 1	MirrorLink in Motion - Allows the PASSENGER to watch videos on multimedia while vehicle is moving by removing the restriction of MirrorLink function while the vehicle is moving. This app is usable if you have retrofitted MIB II unit! ?? FUNCTIONS ON - MirrorLink is available while driving. OFF - MirrorLink not available while driving. ? REQUIREMENTS Use this app only if you are able to use the MirrorLink in still standing and it locks when you start driving! ?? IN-CAR PROCEDURE 1. Turn the ignition ON. Do not start the engine! 2. Let Multimedia to fully start (it takes around 3 minutes) before using this application. 3. After MirrorLink activation, multimedia must be restarted if not restarted automatically. To restart multimedia press and hold power on button for 20s. ?? ATTENTION This functions is disabled for security reasons and helps avoid accidents. It can be very dangerous if the driver is distracted with the video, wherefore we do not recommend nor encourage this function to be activated. Laws in some countries do not allow this function to be enabled. Do this at your own risk! We are not responsible for any loss or damage.
Rear wiper	Activate/Deactivate rear window wiper. ?? FUNCTION Turn OFF or ON the rear window wiper.
Highway lights	Highway lights automatically adjust lights when speed reaches 110 km/h (68 mph) that gives an extra 70 meters (230 feet) of bright visibility and more than two seconds longer to react to an obstacle in the road. ?? FUNCTION Set the highway lights OFF or ON. ? REQUIREMENTS Vehicle must have Xenon headlights and Rain light sensor.
Footwell lights	Use this application after footwell lights installation to activate it. ?? FUNCTION Activate (ON) for LED, Bulb or Deactivate (OFF) Footwell lights ? REQUIREMENTS Footwell lights must be installed in the vehicle.
Remote windows function	Open or close windows via key fob. ?? FUNCTION To turn OFF or ON the comfort windows. ? REQUIREMENTS Windows must be calibrated. ?? IN CAR PROCEDURES In the head unit follow the instruction: 1) Vehicle 2) Setup 3) Open and Close 4) Conv. opening (all windows or drivers window)
Headlight washer	?? FUNCTION Turn ON or OFF Headlights Washer System. ? REQUIREMENTS Vehicle must have Headlights Washing System installed. ?? ATTENTION Deactivating the Headlights Washing System with Xenon headlights is prohibited and is against the law in some countries.
DRL settings	DRL- Daytime Running Lights. ?? FUNCTION DRL OFF - Deactivate (OFF) Daytime Runnings Lights DRL via Separate lights DRL via Fog Lights - Daytime Running Lights active on Fog Lights DRL via Headlights and Fog lights - Daytime Running Lights active both on Headlights and Fog lights
High beam speed threshold	Speed threshold above which the high beam assist will activate high beams. ?? FUNCTION Adjust High Beam Speed Threshold ? REQUIREMENTS Vehicle must have High Beam Assist ?? ATTENTION The light from beam headlights may cause glare. Use low beam headlights when you meet oncoming vehicles or approach another vehicle from behind. You should also use low beams in lighted areas, such as cities. To avoid blinding yourself you should also use low beams when driving in fog, heavy rain, or snow.
Start/Stop System Deactivation	Start/Stop system - automatically shuts down and restarts the engine to reduce the amount of time the engine spends idling, thereby reducing fuel consumption and emissions ⚙ Fonctions You can temporarily disable the Start/Stop system by pressing Start/Stop button, but this stays active only until you turn off the engine. This function will permanently disable Start/Stop system 📖 Prérequis The vehicle must have a Start/Stop system installed
Comfort Windows	Open/Close the windows via remote key by holding Lock/Unlock buttons or holding the key rotated for some time in a lock of the door handle 📖 Prérequis The electric windows must be calibrated
Refuel Quantity in Dashboard	This additional view shows how much fuel is needed to fully fill up your tank at the given moment ⚙ Fonctions Enable or disable refuel quantity view ⚠ Attention Works only for GTI, GTD and R
Rear Wiper With Front Wiper (Interval)	?? Functions Enable automatic rear window wiping when front wipers are set to "interval" position
Rear Wiper With Front Wiper (Permanent)	?? Functions Enable automatic rear window wiping when front wipers are set to "permanent" position
Footwell Light Dimming w/Door Open	?? Functions Adjust the footwell light behaviour when door is open - footwell lights off, or lit at brightness 10 - 100% 📖 Prérequis Footwell lights must be installed
Permanent Running Lights	Permanent running lights keep your car visible to other drivers during daytime even when the headlights are switched off ⚙ Fonctions Enable or disable permanent running lights via Low Beam
Consumption Display Correction	If the fuel consumption displayed in the MFD (multi function display) differs compared to real measured fuel consumption, it is possible to adjust the value, so that the correct fuel consumption is displayed. ⚙ Fonctions Adjust the indicated fuel consumption from 85% to 115% 📖 Prérequis Vehicle must have an instrument cluster with multi function display.
Automatic Rain Closing // Fermeture automatique en cas de pluie	Cette fonction ferme automatiquement les vitres et le toit ouvrant de votre véhicule lorsque le capteur de pluie détecte de la pluie.. ⚙ Fonctions OFF - fonction désactivée ON - fonction activée 📖 Prérequis Le détecteur de pluie doit être installé et actif ⚠ Attention Le calibrage des fenêtre doit avoir été effectué (tout comme la fermture en une seule impulsion sur les boutons des feêntres du véhicule en cas de coupure de batterie)
Needle sweep V2	Gauge Test/Needle Sweep - sweep the gauge needles through their full range automatically on your dashboard when you turn the ignition on. ?? FUNCTION Turn ON or OFF needle sweep on your vehicle. ?? ATTENTION V2 - is for the reason is the needle sweep is not supported.
Tail Light Dimming	Select the tail light dimming changing the voltage. ⚙ Fonctions Inactive - Direct battery voltage 12.3V - 7% 12.4V - 14% 12.5V - 21% 12.6V - 28% 12.7V - 35% 12.8V - 42% 12.9V - 49% 13.0V - 56% 13.1V - 63% 13.2V - 70% 13.3V - 77% 13.4V - 84% 13.5V - 91% 13.6V - 100%
Headlight Dimming	Select the headlight dimming changing voltage. ⚙ Fonctions Inactive - Direct battery voltage 12.3V - 7% 12.4V - 14% 12.5V - 21% 12.6V - 28% 12.7V - 35% 12.8V - 42% 12.9V - 49% 13.0V - 56% 13.1V - 63% 13.2V - 70% 13.3V - 77% 13.4V - 84% 13.5V - 91% 13.6V - 100%
Delay Alarm Activation	Select how to start the anti-theft alarm delay. When the door is opened/when the door is unclocked. ⚙ Fonctions Door Opened Door is Unlocked 📖 Prérequis The vehicle must have an original anti-theft system installed.
Lock/Unlock Confirmation Turn Signals	Return message with turn signals when locking/unlocking via remote control. The function is useful to know do the vehicle was been locked or unlocked. ?? FUNCTION Turn OFF or ON lock/unlock confirmation with turn signals. ? REQUIREMENTS Vehicle must have an original alarm security signal.
Lock/Unlock- Horn Confirmation	This application will activate horn lock and unlock confirmation. Having this activated on your vehicle will allow you to walk away from your vehicle knowing that its secure. ?? FUNCTION Turn ON or OFF horn confirmation of locking and unlocking. ? REQUIREMENTS Vehicle must have OEM security system installed.
Comfort Blinking	With the comfort blinker function, the indicator stalk needs to be touched only once for the direction indicators to flash three(by default) times. ?? FUNCTION Turn OFF or ON the comfort blinking function in the vehicle.
Central Locking	Power door locks (also known as electric door locks or central locking) allow the driver or front passenger to simultaneously lock or unlock all the doors of an automobile or truck, by pressing a button or flipping a switch. This one-click application allows to unlock just the driver door and with the second press of the unlock button on the key fob other doors will be unlocked. ?? FUNCTION Set Central Locking to unlock just the driver door or all doors with a press of unlock button on the key fob.
Comfort Operation for Driver's Window	Comfort operation will work only for the driver's window. ?? FUNCTION Turn OFF or ON the comfort operation only for the driver's window. After turning the function ON, hold the unlock button on the remote, and the driver's window will open. Vice versa with the lock button. ? REQUIREMENTS Windows must be calibrated.
Windows/Sunroof with Ignition	Windows/Sunroof power can be swtiched OFF after the Ignition or leaved ON. Adjust the setting of windows/sunroof power after the ignition is switched OFF. ?? FUNCTION Turn OFF or ON windows/sunroof power after the ignition is swtiched OFF.
Enable Rear Wiper with Reverse Gear	If the front windshield wipers are ON, the rear window wiper will turn ON automatically when the vehicle is shifted into R (Reverse) gear ⚙ Fonctions Enable or disable the rear wiper feature in reverse gear 📖 Prérequis Front windshield wipers must be turned ON ✅ Procédure After app activation in the dashboard menu go to Settings -> Convenience -> Factory setting -> OK
Brake Lights with Ignition	After pressing the brake pedal the brake lights start to light. Adjust the settings of brake lights to work or not to work after the ignition is OFF. ?? FUNCTION Turn OFF or ON the function for brake lights to work after the ignition is switched OFF.
Visual Confirmation for Comfort Operation	Comfort Operation - Open/Close the windows from the remote key by holding Lock/Unlock buttons (Lock - will close the windows/Unlock - will open the windows) The visual confirmation will let to know that the comfort operation has been successfully ended. ?? FUNCTION Turn ON or OFF visual confirmation for comfort operation. ? REQUIREMENTS The comfort operation must be turned ON.
Comfort Opening Type for Sunroof	The sunroof have two types for comfort operation. ?? FUNCTION Select to Open or Lift the sunroof in comfort operation. ? REQUIREMENTS The comfort operation for sunroof must be turned ON.
Comfort Operation for Sunroof	Comfort opening and closing for sunroof holding the lock/unlock button on remote. ?? FUNCTION Turn OFF or ON the comfort operation for sunroof. Hold the unlock button on remote key to open the sunroof or hold the lock button to close it.
Comfort Windows Operation in Door Lock	Open or close windows and sunroof using door lock. ?? FUNCTION Turn OFF or ON the comfort windows in the door lock. After turning ON, hold the key in the door lock to unlock position to open or in lock position to close. ? REQUIREMENTS Windows must be calibrated.
Auto Lock Rear Lid	The rear lid auto locks when the vehicle starts moving and accessing speed of 15 km/h. ?? FUNCTION Turn OFF or ON the auto lock of rear lid.
Headlights for Traveling to RHD/LHD	Setting allows to switch the headlights between Left-Hand-Driving (LHD) and Right-Hand-Driving (RHD) when traveling into a country which is opposite to what the vehicle was originally made for. ?? FUNCTION Turn OFF or ON the tourist mode for traveling to RHD/LHD countries. If the vehicle was originaly made for left hand driving, turning the application ON will set the headlights for right hand drive and vice versa.
Rear Fog OFF when High Beams ON	?? FUNCTION Turn OFF or ON the function to turn OFF the rear fog light when the high beams are ON. OFF - the high beams will be active when the rear fog is turned ON. ON - the high beams will be inactive when the rear fog is turned ON.
DRLs Inactive when Turn Signals Active	Daytime running lights (DRLs) inactive with turn signals active. ?? FUNCTION Turn OFF or ON the function to DRLs be inactive when the turn signal is active. ? REQUIREMENTS The vehicle must have daytime running lights be activated.
CH/LH Lights via Low Beams/Fog Lights	CH - Coming Home makes it easier to see your surroundings when you get out of your car in the dark. LH - Leaving Home works by turning on the lights when you use the key fob to unlock your doors. ⚙ Fonctions Change the CH/LH lights to work via low beams or the fog lights. ? REQUIREMENTS CH/LH Lights function must be turned ON.
CH Lights Timer Functionality	CH - Coming Home makes it easier to see your surroundings when you get out of your car in the dark. ?? FUNCTION Change when the coming home lights timer will start to calculate. When Ignition OFF - after the ignition will be switched OFF, CH lights will start to work for the set time. When Door Open - after the doors will be opened, CH lights will start to work for the set time. ? REQUIREMENTS CH Lights function must be turned ON.
CH Lights Mode	CH - Coming Home makes it easier to see your surroundings when you get out of your car in the dark. ?? FUNCTION Switch CH Lights to Auto or Manual. Auto - when it is dark outside. Manual - flash high beams when the ignition is off to activate. ? REQUIREMENTS For Auto CH Lights the auto headlights are required. CH Lights function must be turned ON.
CH/LH Lights	CH - Coming Home makes it easier to see your surroundings when you get out of your car in the dark. LH - Leaving Home works by turning on the lights when you use the key fob to unlock your doors. ⚙ Fonctions Turn ON or OFF CH/LH Lights function. ? REQUIREMENTS The vehicle must have automatic headlights.
Instrument Cluster Language	?? FUNCTION Change the language of the instrument cluster.
Multi Function Indicator	?? FUNCTION Turn OFF or ON the multi function indicator. ? REQUIREMENTS Vehicle must have multi function indicator.
ESC deactivation V2	ESC - Electronic Stability Control (a computerized technology that improves a vehicle's stability by detecting and reducing loss of traction (skidding)). ASR - A traction control system (TCS), also known as ASR Usable when ESC deactivation app doesn't work. ?? FUNCTION Turn OFF the ASR. Turn OFF the ASR and ESC. ?? IN CAR PROCEDURES To disable the ESC press and hold the ESC button for 5 seconds. ?? ATTENTION Not working with ABS units 1K0907379AH/1K0907379AJ/1K0907379BH/1K0907379BJ/1K0907379BK/1K0907379BL ECS function is for security purpose and helps to avoid accidents. We do not encourage or recommend to turn OFF this function.
Auto Folding Mirrors	Auto Folding Mirrors - side mirrors may be manually or electrically folded in, to protect them when the car is parked or being washed in an automated car wash. ⚙ Fonctions Unfold with ignition - fold mirrors after locking via key fob with a long click and unfold after ignition is turned on. Unfold with door - fold mirrors after locking via key fob with long click and unfold after driver door is opened. OFF - Turn OFF Auto folding mirrors. 📖 Pré Requis Folding mirrors must be installed. ?? IN-CAR PROCEDURE After app activation function must be enabled on car multimedia 'MIRRORS AND WIPERS' menu. ?? ATTENTION Only for UDS control modules. Please check this in the doors control modules Information section.
MirrorLink in motion 2	"MirrorLink in Motion - Allows the PASSENGER to watch videos on multimedia while vehicle is moving by removing the restriction of MirrorLink function while the vehicle is moving. This app is usable if you have retrofitted MIB II unit! Use this app if "MirrorLink in motion 1" is NOT SUPPORTED. ?? FUNCTIONS ON - MirrorLink is available while driving. OFF - MirrorLink not available while driving. ? REQUIREMENTS Use this app only if you are able to use the MirrorLink in still standing and it locks when you start driving! ?? IN-CAR PROCEDURE 1. Turn the ignition ON. Do not start the engine! 2. Let Multimedia to fully start (it takes around 3 minutes) before using this application. 3. After MirrorLink activation, multimedia must be restarted if not restarted automatically. To restart multimedia press and hold power on button for 20s. ?? ATTENTION This functions is disabled for security reasons and helps avoid accidents. It can be very dangerous if the driver is distracted with the video, wherefore we do not recommend nor encourage this function to be activated. Laws in some countries do not allow this function to be enabled. Do this at your own risk! We are not responsible for any loss or damage.
MirrorLink in motion 1	MirrorLink in Motion - Allows the PASSENGER to watch videos on multimedia while vehicle is moving by removing the restriction of MirrorLink function while the vehicle is moving. This app is usable if you have retrofitted MIB II unit! ?? FUNCTIONS ON - MirrorLink is available while driving. OFF - MirrorLink not available while driving. ? REQUIREMENTS Use this app only if you are able to use the MirrorLink in still standing and it locks when you start driving! ?? IN-CAR PROCEDURE 1. Turn the ignition ON. Do not start the engine! 2. Let Multimedia to fully start (it takes around 3 minutes) before using this application. 3. After MirrorLink activation, multimedia must be restarted if not restarted automatically. To restart multimedia press and hold power on button for 20s. ?? ATTENTION This functions is disabled for security reasons and helps avoid accidents. It can be very dangerous if the driver is distracted with the video, wherefore we do not recommend nor encourage this function to be activated. Laws in some countries do not allow this function to be enabled. Do this at your own risk! We are not responsible for any loss or damage.
Rear wiper	Activate/Deactivate rear window wiper. ?? FUNCTION Turn OFF or ON the rear window wiper.
Highway lights	Highway lights automatically adjust lights when speed reaches 110 km/h (68 mph) that gives an extra 70 meters (230 feet) of bright visibility and more than two seconds longer to react to an obstacle in the road. ?? FUNCTION Set the highway lights OFF or ON. ? REQUIREMENTS Vehicle must have Xenon headlights and Rain light sensor.
Footwell lights	Use this application after footwell lights installation to activate it. ?? FUNCTION Activate (ON) for LED, Bulb or Deactivate (OFF) Footwell lights ? REQUIREMENTS Footwell lights must be installed in the vehicle.
Remote windows function	Open or close windows via key fob. ?? FUNCTION To turn OFF or ON the comfort windows. ? REQUIREMENTS Windows must be calibrated. ?? IN CAR PROCEDURES In the head unit follow the instruction: 1) Vehicle 2) Setup 3) Open and Close 4) Conv. opening (all windows or drivers window)
Headlight washer	?? FUNCTION Turn ON or OFF Headlights Washer System. ? REQUIREMENTS Vehicle must have Headlights Washing System installed. ?? ATTENTION Deactivating the Headlights Washing System with Xenon headlights is prohibited and is against the law in some countries.
DRL settings	DRL- Daytime Running Lights. ?? FUNCTION DRL OFF - Deactivate (OFF) Daytime Runnings Lights DRL via Separate lights DRL via Fog Lights - Daytime Running Lights active on Fog Lights DRL via Headlights and Fog lights - Daytime Running Lights active both on Headlights and Fog lights
High beam speed threshold	Speed threshold above which the high beam assist will activate high beams. ?? FUNCTION Adjust High Beam Speed Threshold ? REQUIREMENTS Vehicle must have High Beam Assist ?? ATTENTION The light from beam headlights may cause glare. Use low beam headlights when you meet oncoming vehicles or approach another vehicle from behind. You should also use low beams in lighted areas, such as cities. To avoid blinding yourself you should also use low beams when driving in fog, heavy rain, or snow.
Start/Stop System Deactivation	Start/Stop system - automatically shuts down and restarts the engine to reduce the amount of time the engine spends idling, thereby reducing fuel consumption and emissions ⚙ Fonctions You can temporarily disable the Start/Stop system by pressing Start/Stop button, but this stays active only until you turn off the engine. This function will permanently disable Start/Stop system 📖 Prérequis The vehicle must have a Start/Stop system installed
Comfort Windows	Open/Close the windows via remote key by holding Lock/Unlock buttons or holding the key rotated for some time in a lock of the door handle 📖 Prérequis The electric windows must be calibrated
Refuel Quantity in Dashboard	This additional view shows how much fuel is needed to fully fill up your tank at the given moment ⚙ Fonctions Enable or disable refuel quantity view ⚠ Attention Works only for GTI, GTD and R
Rear Wiper With Front Wiper (Interval)	?? Functions Enable automatic rear window wiping when front wipers are set to "interval" position
Rear Wiper With Front Wiper (Permanent)	?? Functions Enable automatic rear window wiping when front wipers are set to "permanent" position
Footwell Light Dimming w/Door Open	?? Functions Adjust the footwell light behaviour when door is open - footwell lights off, or lit at brightness 10 - 100% 📖 Prérequis Footwell lights must be installed
Permanent Running Lights	Permanent running lights keep your car visible to other drivers during daytime even when the headlights are switched off ⚙ Fonctions Enable or disable permanent running lights via Low Beam
Consumption Display Correction	If the fuel consumption displayed in the MFD (multi function display) differs compared to real measured fuel consumption, it is possible to adjust the value, so that the correct fuel consumption is displayed. ⚙ Fonctions Adjust the indicated fuel consumption from 85% to 115% 📖 Prérequis Vehicle must have an instrument cluster with multi function display.
Automatic Rain Closing // Fermeture automatique en cas de pluie	Cette fonction ferme automatiquement les vitres et le toit ouvrant de votre véhicule lorsque le capteur de pluie détecte de la pluie.. ⚙ Fonctions OFF - fonction désactivée ON - fonction activée 📖 Prérequis Le détecteur de pluie doit être installé et actif ⚠ Attention Le calibrage des fenêtre doit avoir été effectué (tout comme la fermture en une seule impulsion sur les boutons des feêntres du véhicule en cas de coupure de batterie)
Needle sweep V2	Gauge Test/Needle Sweep - sweep the gauge needles through their full range automatically on your dashboard when you turn the ignition on. ?? FUNCTION Turn ON or OFF needle sweep on your vehicle. ?? ATTENTION V2 - is for the reason is the needle sweep is not supported.
Tail Light Dimming	Select the tail light dimming changing the voltage. ⚙ Fonctions Inactive - Direct battery voltage 12.3V - 7% 12.4V - 14% 12.5V - 21% 12.6V - 28% 12.7V - 35% 12.8V - 42% 12.9V - 49% 13.0V - 56% 13.1V - 63% 13.2V - 70% 13.3V - 77% 13.4V - 84% 13.5V - 91% 13.6V - 100%
Headlight Dimming	Select the headlight dimming changing voltage. ⚙ Fonctions Inactive - Direct battery voltage 12.3V - 7% 12.4V - 14% 12.5V - 21% 12.6V - 28% 12.7V - 35% 12.8V - 42% 12.9V - 49% 13.0V - 56% 13.1V - 63% 13.2V - 70% 13.3V - 77% 13.4V - 84% 13.5V - 91% 13.6V - 100%
Delay Alarm Activation	Select how to start the anti-theft alarm delay. When the door is opened/when the door is unclocked. ⚙ Fonctions Door Opened Door is Unlocked 📖 Prérequis The vehicle must have an original anti-theft system installed.
Lock/Unlock Confirmation Turn Signals	Return message with turn signals when locking/unlocking via remote control. The function is useful to know do the vehicle was been locked or unlocked. ?? FUNCTION Turn OFF or ON lock/unlock confirmation with turn signals. ? REQUIREMENTS Vehicle must have an original alarm security signal.
Lock/Unlock- Horn Confirmation	This application will activate horn lock and unlock confirmation. Having this activated on your vehicle will allow you to walk away from your vehicle knowing that its secure. ?? FUNCTION Turn ON or OFF horn confirmation of locking and unlocking. ? REQUIREMENTS Vehicle must have OEM security system installed.
Comfort Blinking	With the comfort blinker function, the indicator stalk needs to be touched only once for the direction indicators to flash three(by default) times. ?? FUNCTION Turn OFF or ON the comfort blinking function in the vehicle.
Central Locking	Power door locks (also known as electric door locks or central locking) allow the driver or front passenger to simultaneously lock or unlock all the doors of an automobile or truck, by pressing a button or flipping a switch. This one-click application allows to unlock just the driver door and with the second press of the unlock button on the key fob other doors will be unlocked. ?? FUNCTION Set Central Locking to unlock just the driver door or all doors with a press of unlock button on the key fob.
Comfort Operation for Driver's Window	Comfort operation will work only for the driver's window. ?? FUNCTION Turn OFF or ON the comfort operation only for the driver's window. After turning the function ON, hold the unlock button on the remote, and the driver's window will open. Vice versa with the lock button. ? REQUIREMENTS Windows must be calibrated.
Windows/Sunroof with Ignition	Windows/Sunroof power can be swtiched OFF after the Ignition or leaved ON. Adjust the setting of windows/sunroof power after the ignition is switched OFF. ?? FUNCTION Turn OFF or ON windows/sunroof power after the ignition is swtiched OFF.
Enable Rear Wiper with Reverse Gear	If the front windshield wipers are ON, the rear window wiper will turn ON automatically when the vehicle is shifted into R (Reverse) gear ⚙ Fonctions Enable or disable the rear wiper feature in reverse gear 📖 Prérequis Front windshield wipers must be turned ON ✅ Procédure After app activation in the dashboard menu go to Settings -> Convenience -> Factory setting -> OK
Brake Lights with Ignition	After pressing the brake pedal the brake lights start to light. Adjust the settings of brake lights to work or not to work after the ignition is OFF. ?? FUNCTION Turn OFF or ON the function for brake lights to work after the ignition is switched OFF.
Visual Confirmation for Comfort Operation	Comfort Operation - Open/Close the windows from the remote key by holding Lock/Unlock buttons (Lock - will close the windows/Unlock - will open the windows) The visual confirmation will let to know that the comfort operation has been successfully ended. ?? FUNCTION Turn ON or OFF visual confirmation for comfort operation. ? REQUIREMENTS The comfort operation must be turned ON.
Comfort Opening Type for Sunroof	The sunroof have two types for comfort operation. ?? FUNCTION Select to Open or Lift the sunroof in comfort operation. ? REQUIREMENTS The comfort operation for sunroof must be turned ON.
Comfort Operation for Sunroof	Comfort opening and closing for sunroof holding the lock/unlock button on remote. ?? FUNCTION Turn OFF or ON the comfort operation for sunroof. Hold the unlock button on remote key to open the sunroof or hold the lock button to close it.
Comfort Windows Operation in Door Lock	Open or close windows and sunroof using door lock. ?? FUNCTION Turn OFF or ON the comfort windows in the door lock. After turning ON, hold the key in the door lock to unlock position to open or in lock position to close. ? REQUIREMENTS Windows must be calibrated.
Auto Lock Rear Lid	The rear lid auto locks when the vehicle starts moving and accessing speed of 15 km/h. ?? FUNCTION Turn OFF or ON the auto lock of rear lid.
Headlights for Traveling to RHD/LHD	Setting allows to switch the headlights between Left-Hand-Driving (LHD) and Right-Hand-Driving (RHD) when traveling into a country which is opposite to what the vehicle was originally made for. ?? FUNCTION Turn OFF or ON the tourist mode for traveling to RHD/LHD countries. If the vehicle was originaly made for left hand driving, turning the application ON will set the headlights for right hand drive and vice versa.
Rear Fog OFF when High Beams ON	?? FUNCTION Turn OFF or ON the function to turn OFF the rear fog light when the high beams are ON. OFF - the high beams will be active when the rear fog is turned ON. ON - the high beams will be inactive when the rear fog is turned ON.
DRLs Inactive when Turn Signals Active	Daytime running lights (DRLs) inactive with turn signals active. ?? FUNCTION Turn OFF or ON the function to DRLs be inactive when the turn signal is active. ? REQUIREMENTS The vehicle must have daytime running lights be activated.
CH/LH Lights via Low Beams/Fog Lights	CH - Coming Home makes it easier to see your surroundings when you get out of your car in the dark. LH - Leaving Home works by turning on the lights when you use the key fob to unlock your doors. ⚙ Fonctions Change the CH/LH lights to work via low beams or the fog lights. ? REQUIREMENTS CH/LH Lights function must be turned ON.
CH Lights Timer Functionality	CH - Coming Home makes it easier to see your surroundings when you get out of your car in the dark. ?? FUNCTION Change when the coming home lights timer will start to calculate. When Ignition OFF - after the ignition will be switched OFF, CH lights will start to work for the set time. When Door Open - after the doors will be opened, CH lights will start to work for the set time. ? REQUIREMENTS CH Lights function must be turned ON.
CH Lights Mode	CH - Coming Home makes it easier to see your surroundings when you get out of your car in the dark. ?? FUNCTION Switch CH Lights to Auto or Manual. Auto - when it is dark outside. Manual - flash high beams when the ignition is off to activate. ? REQUIREMENTS For Auto CH Lights the auto headlights are required. CH Lights function must be turned ON.
CH/LH Lights	CH - Coming Home makes it easier to see your surroundings when you get out of your car in the dark. LH - Leaving Home works by turning on the lights when you use the key fob to unlock your doors. ⚙ Fonctions Turn ON or OFF CH/LH Lights function. ? REQUIREMENTS The vehicle must have automatic headlights.
Instrument Cluster Language	?? FUNCTION Change the language of the instrument cluster.
Multi Function Indicator	?? FUNCTION Turn OFF or ON the multi function indicator. ? REQUIREMENTS Vehicle must have multi function indicator.
ESC deactivation V2	ESC - Electronic Stability Control (a computerized technology that improves a vehicle's stability by detecting and reducing loss of traction (skidding)). ASR - A traction control system (TCS), also known as ASR Usable when ESC deactivation app doesn't work. ?? FUNCTION Turn OFF the ASR. Turn OFF the ASR and ESC. ?? IN CAR PROCEDURES To disable the ESC press and hold the ESC button for 5 seconds. ?? ATTENTION Not working with ABS units 1K0907379AH/1K0907379AJ/1K0907379BH/1K0907379BJ/1K0907379BK/1K0907379BL ECS function is for security purpose and helps to avoid accidents. We do not encourage or recommend to turn OFF this function.
Auto Folding Mirrors	Auto Folding Mirrors - side mirrors may be manually or electrically folded in, to protect them when the car is parked or being washed in an automated car wash. ⚙ Fonctions Unfold with ignition - fold mirrors after locking via key fob with a long click and unfold after ignition is turned on. Unfold with door - fold mirrors after locking via key fob with long click and unfold after driver door is opened. OFF - Turn OFF Auto folding mirrors. 📖 Pré Requis Folding mirrors must be installed. ?? IN-CAR PROCEDURE After app activation function must be enabled on car multimedia 'MIRRORS AND WIPERS' menu. ?? ATTENTION Only for UDS control modules. Please check this in the doors control modules Information section.
MirrorLink in motion 2	"MirrorLink in Motion - Allows the PASSENGER to watch videos on multimedia while vehicle is moving by removing the restriction of MirrorLink function while the vehicle is moving. This app is usable if you have retrofitted MIB II unit! Use this app if "MirrorLink in motion 1" is NOT SUPPORTED. ?? FUNCTIONS ON - MirrorLink is available while driving. OFF - MirrorLink not available while driving. ? REQUIREMENTS Use this app only if you are able to use the MirrorLink in still standing and it locks when you start driving! ?? IN-CAR PROCEDURE 1. Turn the ignition ON. Do not start the engine! 2. Let Multimedia to fully start (it takes around 3 minutes) before using this application. 3. After MirrorLink activation, multimedia must be restarted if not restarted automatically. To restart multimedia press and hold power on button for 20s. ?? ATTENTION This functions is disabled for security reasons and helps avoid accidents. It can be very dangerous if the driver is distracted with the video, wherefore we do not recommend nor encourage this function to be activated. Laws in some countries do not allow this function to be enabled. Do this at your own risk! We are not responsible for any loss or damage.
MirrorLink in motion 1	MirrorLink in Motion - Allows the PASSENGER to watch videos on multimedia while vehicle is moving by removing the restriction of MirrorLink function while the vehicle is moving. This app is usable if you have retrofitted MIB II unit! ?? FUNCTIONS ON - MirrorLink is available while driving. OFF - MirrorLink not available while driving. ? REQUIREMENTS Use this app only if you are able to use the MirrorLink in still standing and it locks when you start driving! ?? IN-CAR PROCEDURE 1. Turn the ignition ON. Do not start the engine! 2. Let Multimedia to fully start (it takes around 3 minutes) before using this application. 3. After MirrorLink activation, multimedia must be restarted if not restarted automatically. To restart multimedia press and hold power on button for 20s. ?? ATTENTION This functions is disabled for security reasons and helps avoid accidents. It can be very dangerous if the driver is distracted with the video, wherefore we do not recommend nor encourage this function to be activated. Laws in some countries do not allow this function to be enabled. Do this at your own risk! We are not responsible for any loss or damage.
Rear wiper	Activate/Deactivate rear window wiper. ?? FUNCTION Turn OFF or ON the rear window wiper.
Highway lights	Highway lights automatically adjust lights when speed reaches 110 km/h (68 mph) that gives an extra 70 meters (230 feet) of bright visibility and more than two seconds longer to react to an obstacle in the road. ?? FUNCTION Set the highway lights OFF or ON. ? REQUIREMENTS Vehicle must have Xenon headlights and Rain light sensor.
Footwell lights	Use this application after footwell lights installation to activate it. ?? FUNCTION Activate (ON) for LED, Bulb or Deactivate (OFF) Footwell lights ? REQUIREMENTS Footwell lights must be installed in the vehicle.
Remote windows function	Open or close windows via key fob. ?? FUNCTION To turn OFF or ON the comfort windows. ? REQUIREMENTS Windows must be calibrated. ?? IN CAR PROCEDURES In the head unit follow the instruction: 1) Vehicle 2) Setup 3) Open and Close 4) Conv. opening (all windows or drivers window)
Headlight washer	?? FUNCTION Turn ON or OFF Headlights Washer System. ? REQUIREMENTS Vehicle must have Headlights Washing System installed. ?? ATTENTION Deactivating the Headlights Washing System with Xenon headlights is prohibited and is against the law in some countries.
DRL settings	DRL- Daytime Running Lights. ?? FUNCTION DRL OFF - Deactivate (OFF) Daytime Runnings Lights DRL via Separate lights DRL via Fog Lights - Daytime Running Lights active on Fog Lights DRL via Headlights and Fog lights - Daytime Running Lights active both on Headlights and Fog lights
High beam speed threshold	Speed threshold above which the high beam assist will activate high beams. ?? FUNCTION Adjust High Beam Speed Threshold ? REQUIREMENTS Vehicle must have High Beam Assist ?? ATTENTION The light from beam headlights may cause glare. Use low beam headlights when you meet oncoming vehicles or approach another vehicle from behind. You should also use low beams in lighted areas, such as cities. To avoid blinding yourself you should also use low beams when driving in fog, heavy rain, or snow.
Start/Stop System Deactivation	Start/Stop system - automatically shuts down and restarts the engine to reduce the amount of time the engine spends idling, thereby reducing fuel consumption and emissions ⚙ Fonctions You can temporarily disable the Start/Stop system by pressing Start/Stop button, but this stays active only until you turn off the engine. This function will permanently disable Start/Stop system 📖 Prérequis The vehicle must have a Start/Stop system installed
Comfort Windows	Open/Close the windows via remote key by holding Lock/Unlock buttons or holding the key rotated for some time in a lock of the door handle 📖 Prérequis The electric windows must be calibrated
Refuel Quantity in Dashboard	This additional view shows how much fuel is needed to fully fill up your tank at the given moment ⚙ Fonctions Enable or disable refuel quantity view ⚠ Attention Works only for GTI, GTD and R
Rear Wiper With Front Wiper (Interval)	?? Functions Enable automatic rear window wiping when front wipers are set to "interval" position
Rear Wiper With Front Wiper (Permanent)	?? Functions Enable automatic rear window wiping when front wipers are set to "permanent" position
Footwell Light Dimming w/Door Open	?? Functions Adjust the footwell light behaviour when door is open - footwell lights off, or lit at brightness 10 - 100% 📖 Prérequis Footwell lights must be installed
Permanent Running Lights	Permanent running lights keep your car visible to other drivers during daytime even when the headlights are switched off ⚙ Fonctions Enable or disable permanent running lights via Low Beam
Consumption Display Correction	If the fuel consumption displayed in the MFD (multi function display) differs compared to real measured fuel consumption, it is possible to adjust the value, so that the correct fuel consumption is displayed. ⚙ Fonctions Adjust the indicated fuel consumption from 85% to 115% 📖 Prérequis Vehicle must have an instrument cluster with multi function display.
Automatic Rain Closing // Fermeture automatique en cas de pluie	Cette fonction ferme automatiquement les vitres et le toit ouvrant de votre véhicule lorsque le capteur de pluie détecte de la pluie.. ⚙ Fonctions OFF - fonction désactivée ON - fonction activée 📖 Prérequis Le détecteur de pluie doit être installé et actif ⚠ Attention Le calibrage des fenêtre doit avoir été effectué (tout comme la fermture en une seule impulsion sur les boutons des feêntres du véhicule en cas de coupure de batterie)
Needle sweep V2	Gauge Test/Needle Sweep - sweep the gauge needles through their full range automatically on your dashboard when you turn the ignition on. ?? FUNCTION Turn ON or OFF needle sweep on your vehicle. ?? ATTENTION V2 - is for the reason is the needle sweep is not supported.
Tail Light Dimming	Select the tail light dimming changing the voltage. ⚙ Fonctions Inactive - Direct battery voltage 12.3V - 7% 12.4V - 14% 12.5V - 21% 12.6V - 28% 12.7V - 35% 12.8V - 42% 12.9V - 49% 13.0V - 56% 13.1V - 63% 13.2V - 70% 13.3V - 77% 13.4V - 84% 13.5V - 91% 13.6V - 100%
Headlight Dimming	Select the headlight dimming changing voltage. ⚙ Fonctions Inactive - Direct battery voltage 12.3V - 7% 12.4V - 14% 12.5V - 21% 12.6V - 28% 12.7V - 35% 12.8V - 42% 12.9V - 49% 13.0V - 56% 13.1V - 63% 13.2V - 70% 13.3V - 77% 13.4V - 84% 13.5V - 91% 13.6V - 100%
Delay Alarm Activation	Select how to start the anti-theft alarm delay. When the door is opened/when the door is unclocked. ⚙ Fonctions Door Opened Door is Unlocked 📖 Prérequis The vehicle must have an original anti-theft system installed.
Lock/Unlock Confirmation Turn Signals	Return message with turn signals when locking/unlocking via remote control. The function is useful to know do the vehicle was been locked or unlocked. ?? FUNCTION Turn OFF or ON lock/unlock confirmation with turn signals. ? REQUIREMENTS Vehicle must have an original alarm security signal.
Lock/Unlock- Horn Confirmation	This application will activate horn lock and unlock confirmation. Having this activated on your vehicle will allow you to walk away from your vehicle knowing that its secure. ?? FUNCTION Turn ON or OFF horn confirmation of locking and unlocking. ? REQUIREMENTS Vehicle must have OEM security system installed.
Comfort Blinking	With the comfort blinker function, the indicator stalk needs to be touched only once for the direction indicators to flash three(by default) times. ?? FUNCTION Turn OFF or ON the comfort blinking function in the vehicle.
Central Locking	Power door locks (also known as electric door locks or central locking) allow the driver or front passenger to simultaneously lock or unlock all the doors of an automobile or truck, by pressing a button or flipping a switch. This one-click application allows to unlock just the driver door and with the second press of the unlock button on the key fob other doors will be unlocked. ?? FUNCTION Set Central Locking to unlock just the driver door or all doors with a press of unlock button on the key fob.
Comfort Operation for Driver's Window	Comfort operation will work only for the driver's window. ?? FUNCTION Turn OFF or ON the comfort operation only for the driver's window. After turning the function ON, hold the unlock button on the remote, and the driver's window will open. Vice versa with the lock button. ? REQUIREMENTS Windows must be calibrated.
Windows/Sunroof with Ignition	Windows/Sunroof power can be swtiched OFF after the Ignition or leaved ON. Adjust the setting of windows/sunroof power after the ignition is switched OFF. ?? FUNCTION Turn OFF or ON windows/sunroof power after the ignition is swtiched OFF.
Enable Rear Wiper with Reverse Gear	If the front windshield wipers are ON, the rear window wiper will turn ON automatically when the vehicle is shifted into R (Reverse) gear ⚙ Fonctions Enable or disable the rear wiper feature in reverse gear 📖 Prérequis Front windshield wipers must be turned ON ✅ Procédure After app activation in the dashboard menu go to Settings -> Convenience -> Factory setting -> OK
Brake Lights with Ignition	After pressing the brake pedal the brake lights start to light. Adjust the settings of brake lights to work or not to work after the ignition is OFF. ?? FUNCTION Turn OFF or ON the function for brake lights to work after the ignition is switched OFF.
Visual Confirmation for Comfort Operation	Comfort Operation - Open/Close the windows from the remote key by holding Lock/Unlock buttons (Lock - will close the windows/Unlock - will open the windows) The visual confirmation will let to know that the comfort operation has been successfully ended. ?? FUNCTION Turn ON or OFF visual confirmation for comfort operation. ? REQUIREMENTS The comfort operation must be turned ON.
Comfort Opening Type for Sunroof	The sunroof have two types for comfort operation. ?? FUNCTION Select to Open or Lift the sunroof in comfort operation. ? REQUIREMENTS The comfort operation for sunroof must be turned ON.
Comfort Operation for Sunroof	Comfort opening and closing for sunroof holding the lock/unlock button on remote. ?? FUNCTION Turn OFF or ON the comfort operation for sunroof. Hold the unlock button on remote key to open the sunroof or hold the lock button to close it.
Comfort Windows Operation in Door Lock	Open or close windows and sunroof using door lock. ?? FUNCTION Turn OFF or ON the comfort windows in the door lock. After turning ON, hold the key in the door lock to unlock position to open or in lock position to close. ? REQUIREMENTS Windows must be calibrated.
Auto Lock Rear Lid	The rear lid auto locks when the vehicle starts moving and accessing speed of 15 km/h. ?? FUNCTION Turn OFF or ON the auto lock of rear lid.
Headlights for Traveling to RHD/LHD	Setting allows to switch the headlights between Left-Hand-Driving (LHD) and Right-Hand-Driving (RHD) when traveling into a country which is opposite to what the vehicle was originally made for. ?? FUNCTION Turn OFF or ON the tourist mode for traveling to RHD/LHD countries. If the vehicle was originaly made for left hand driving, turning the application ON will set the headlights for right hand drive and vice versa.
Rear Fog OFF when High Beams ON	?? FUNCTION Turn OFF or ON the function to turn OFF the rear fog light when the high beams are ON. OFF - the high beams will be active when the rear fog is turned ON. ON - the high beams will be inactive when the rear fog is turned ON.
DRLs Inactive when Turn Signals Active	Daytime running lights (DRLs) inactive with turn signals active. ?? FUNCTION Turn OFF or ON the function to DRLs be inactive when the turn signal is active. ? REQUIREMENTS The vehicle must have daytime running lights be activated.
CH/LH Lights via Low Beams/Fog Lights	CH - Coming Home makes it easier to see your surroundings when you get out of your car in the dark. LH - Leaving Home works by turning on the lights when you use the key fob to unlock your doors. ⚙ Fonctions Change the CH/LH lights to work via low beams or the fog lights. ? REQUIREMENTS CH/LH Lights function must be turned ON.
CH Lights Timer Functionality	CH - Coming Home makes it easier to see your surroundings when you get out of your car in the dark. ?? FUNCTION Change when the coming home lights timer will start to calculate. When Ignition OFF - after the ignition will be switched OFF, CH lights will start to work for the set time. When Door Open - after the doors will be opened, CH lights will start to work for the set time. ? REQUIREMENTS CH Lights function must be turned ON.
CH Lights Mode	CH - Coming Home makes it easier to see your surroundings when you get out of your car in the dark. ?? FUNCTION Switch CH Lights to Auto or Manual. Auto - when it is dark outside. Manual - flash high beams when the ignition is off to activate. ? REQUIREMENTS For Auto CH Lights the auto headlights are required. CH Lights function must be turned ON.
CH/LH Lights	CH - Coming Home makes it easier to see your surroundings when you get out of your car in the dark. LH - Leaving Home works by turning on the lights when you use the key fob to unlock your doors. ⚙ Fonctions Turn ON or OFF CH/LH Lights function. ? REQUIREMENTS The vehicle must have automatic headlights.
Instrument Cluster Language	?? FUNCTION Change the language of the instrument cluster.
Multi Function Indicator	?? FUNCTION Turn OFF or ON the multi function indicator. ? REQUIREMENTS Vehicle must have multi function indicator.
ESC deactivation V2	ESC - Electronic Stability Control (a computerized technology that improves a vehicle's stability by detecting and reducing loss of traction (skidding)). ASR - A traction control system (TCS), also known as ASR Usable when ESC deactivation app doesn't work. ?? FUNCTION Turn OFF the ASR. Turn OFF the ASR and ESC. ?? IN CAR PROCEDURES To disable the ESC press and hold the ESC button for 5 seconds. ?? ATTENTION Not working with ABS units 1K0907379AH/1K0907379AJ/1K0907379BH/1K0907379BJ/1K0907379BK/1K0907379BL ECS function is for security purpose and helps to avoid accidents. We do not encourage or recommend to turn OFF this function.
Auto Folding Mirrors	Auto Folding Mirrors - side mirrors may be manually or electrically folded in, to protect them when the car is parked or being washed in an automated car wash. ⚙ Fonctions Unfold with ignition - fold mirrors after locking via key fob with a long click and unfold after ignition is turned on. Unfold with door - fold mirrors after locking via key fob with long click and unfold after driver door is opened. OFF - Turn OFF Auto folding mirrors. 📖 Pré Requis Folding mirrors must be installed. ?? IN-CAR PROCEDURE After app activation function must be enabled on car multimedia 'MIRRORS AND WIPERS' menu. ?? ATTENTION Only for UDS control modules. Please check this in the doors control modules Information section.
MirrorLink in motion 2	"MirrorLink in Motion - Allows the PASSENGER to watch videos on multimedia while vehicle is moving by removing the restriction of MirrorLink function while the vehicle is moving. This app is usable if you have retrofitted MIB II unit! Use this app if "MirrorLink in motion 1" is NOT SUPPORTED. ?? FUNCTIONS ON - MirrorLink is available while driving. OFF - MirrorLink not available while driving. ? REQUIREMENTS Use this app only if you are able to use the MirrorLink in still standing and it locks when you start driving! ?? IN-CAR PROCEDURE 1. Turn the ignition ON. Do not start the engine! 2. Let Multimedia to fully start (it takes around 3 minutes) before using this application. 3. After MirrorLink activation, multimedia must be restarted if not restarted automatically. To restart multimedia press and hold power on button for 20s. ?? ATTENTION This functions is disabled for security reasons and helps avoid accidents. It can be very dangerous if the driver is distracted with the video, wherefore we do not recommend nor encourage this function to be activated. Laws in some countries do not allow this function to be enabled. Do this at your own risk! We are not responsible for any loss or damage.
MirrorLink in motion 1	MirrorLink in Motion - Allows the PASSENGER to watch videos on multimedia while vehicle is moving by removing the restriction of MirrorLink function while the vehicle is moving. This app is usable if you have retrofitted MIB II unit! ?? FUNCTIONS ON - MirrorLink is available while driving. OFF - MirrorLink not available while driving. ? REQUIREMENTS Use this app only if you are able to use the MirrorLink in still standing and it locks when you start driving! ?? IN-CAR PROCEDURE 1. Turn the ignition ON. Do not start the engine! 2. Let Multimedia to fully start (it takes around 3 minutes) before using this application. 3. After MirrorLink activation, multimedia must be restarted if not restarted automatically. To restart multimedia press and hold power on button for 20s. ?? ATTENTION This functions is disabled for security reasons and helps avoid accidents. It can be very dangerous if the driver is distracted with the video, wherefore we do not recommend nor encourage this function to be activated. Laws in some countries do not allow this function to be enabled. Do this at your own risk! We are not responsible for any loss or damage.
Rear wiper	Activate/Deactivate rear window wiper. ?? FUNCTION Turn OFF or ON the rear window wiper.
Highway lights	Highway lights automatically adjust lights when speed reaches 110 km/h (68 mph) that gives an extra 70 meters (230 feet) of bright visibility and more than two seconds longer to react to an obstacle in the road. ?? FUNCTION Set the highway lights OFF or ON. ? REQUIREMENTS Vehicle must have Xenon headlights and Rain light sensor.
Footwell lights	Use this application after footwell lights installation to activate it. ?? FUNCTION Activate (ON) for LED, Bulb or Deactivate (OFF) Footwell lights ? REQUIREMENTS Footwell lights must be installed in the vehicle.
Remote windows function	Open or close windows via key fob. ?? FUNCTION To turn OFF or ON the comfort windows. ? REQUIREMENTS Windows must be calibrated. ?? IN CAR PROCEDURES In the head unit follow the instruction: 1) Vehicle 2) Setup 3) Open and Close 4) Conv. opening (all windows or drivers window)
Headlight washer	?? FUNCTION Turn ON or OFF Headlights Washer System. ? REQUIREMENTS Vehicle must have Headlights Washing System installed. ?? ATTENTION Deactivating the Headlights Washing System with Xenon headlights is prohibited and is against the law in some countries.
DRL settings	DRL- Daytime Running Lights. ?? FUNCTION DRL OFF - Deactivate (OFF) Daytime Runnings Lights DRL via Separate lights DRL via Fog Lights - Daytime Running Lights active on Fog Lights DRL via Headlights and Fog lights - Daytime Running Lights active both on Headlights and Fog lights
High beam speed threshold	Speed threshold above which the high beam assist will activate high beams. ?? FUNCTION Adjust High Beam Speed Threshold ? REQUIREMENTS Vehicle must have High Beam Assist ?? ATTENTION The light from beam headlights may cause glare. Use low beam headlights when you meet oncoming vehicles or approach another vehicle from behind. You should also use low beams in lighted areas, such as cities. To avoid blinding yourself you should also use low beams when driving in fog, heavy rain, or snow.
One-Touch Power Windows Settings	Adjust one-touch/auto power window behavior once a door is open. ⚙ Fonctions Stop
One-Touch Power Windows Settings	Adjust one-touch/auto power window behavior once a door is open. ⚙ Fonctions Stop
One-Touch Power Windows Settings	Adjust one-touch/auto power window behavior once a door is open. ⚙ Fonctions Stop
One-Touch Power Windows Settings	Adjust one-touch/auto power window behavior once a door is open. ⚙ Fonctions Stop
Mirror Dip V1	Mirror Dip feature automatically lowers the passenger side mirror when reverse gear is selected. This provides visibility of the lower side of the car and helps to see the edge of the sidewalk, which simplifies parking. 📖 Prérequis Vehicle must have mirrors with memory function. ? Compatibility Check This app only works with KWP2000 control units. To find out the protocol of your control unit: 1. Go to the Control Units list. 2. Select 52 Passenger Door. 3. Click on Info. 4. Look for the Protocol section at the bottom. It should say TP2.0: KWP2000. ✅ Procédure To activate mirros dip: 1. Set mirror switch to the R position. 2. Engage R gear. ⚠ Attention
Mirror Dip V1	Mirror Dip feature automatically lowers the passenger side mirror when reverse gear is selected. This provides visibility of the lower side of the car and helps to see the edge of the sidewalk, which simplifies parking. 📖 Prérequis Vehicle must have mirrors with memory function. ? Compatibility Check This app only works with KWP2000 control units. To find out the protocol of your control unit: 1. Go to the Control Units list. 2. Select 52 Passenger Door. 3. Click on Info. 4. Look for the Protocol section at the bottom. It should say TP2.0: KWP2000. ✅ Procédure To activate mirros dip: 1. Set mirror switch to the R position. 2. Engage R gear. ⚠ Attention
Mirror Dip V1	Mirror Dip feature automatically lowers the passenger side mirror when reverse gear is selected. This provides visibility of the lower side of the car and helps to see the edge of the sidewalk, which simplifies parking. 📖 Prérequis Vehicle must have mirrors with memory function. ? Compatibility Check This app only works with KWP2000 control units. To find out the protocol of your control unit: 1. Go to the Control Units list. 2. Select 52 Passenger Door. 3. Click on Info. 4. Look for the Protocol section at the bottom. It should say TP2.0: KWP2000. ✅ Procédure To activate mirros dip: 1. Set mirror switch to the R position. 2. Engage R gear. ⚠ Attention
Mirror Dip V1	Mirror Dip feature automatically lowers the passenger side mirror when reverse gear is selected. This provides visibility of the lower side of the car and helps to see the edge of the sidewalk, which simplifies parking. 📖 Prérequis Vehicle must have mirrors with memory function. ? Compatibility Check This app only works with KWP2000 control units. To find out the protocol of your control unit: 1. Go to the Control Units list. 2. Select 52 Passenger Door. 3. Click on Info. 4. Look for the Protocol section at the bottom. It should say TP2.0: KWP2000. ✅ Procédure To activate mirros dip: 1. Set mirror switch to the R position. 2. Engage R gear. ⚠ Attention
High beam assist city recognition	High Beam Assist - dips your high beam automatically to improve driver control and safety for both the driver and other road users. The system is automatically activated when travelling over 37mph with your dipped beams on. This application allows to change high beam assist behavior when entering city. ?? FUNCTION Always - automatically activate low beams when entering city. If Necessary - automatically activate low beam when entering city, only if necessary. ? REQUIREMENTS Vehicle must have high beam assist.
High beam assist city recognition	High Beam Assist - dips your high beam automatically to improve driver control and safety for both the driver and other road users. The system is automatically activated when travelling over 37mph with your dipped beams on. This application allows to change high beam assist behavior when entering city. ?? FUNCTION Always - automatically activate low beams when entering city. If Necessary - automatically activate low beam when entering city, only if necessary. ? REQUIREMENTS Vehicle must have high beam assist.
High beam assist city recognition	High Beam Assist - dips your high beam automatically to improve driver control and safety for both the driver and other road users. The system is automatically activated when travelling over 37mph with your dipped beams on. This application allows to change high beam assist behavior when entering city. ?? FUNCTION Always - automatically activate low beams when entering city. If Necessary - automatically activate low beam when entering city, only if necessary. ? REQUIREMENTS Vehicle must have high beam assist.
High beam assist city recognition	High Beam Assist - dips your high beam automatically to improve driver control and safety for both the driver and other road users. The system is automatically activated when travelling over 37mph with your dipped beams on. This application allows to change high beam assist behavior when entering city. ?? FUNCTION Always - automatically activate low beams when entering city. If Necessary - automatically activate low beam when entering city, only if necessary. ? REQUIREMENTS Vehicle must have high beam assist.
Rain lights	Rain lights improve visibility while driving in rain or snow. ⚙ Fonctions Turn ON or OFF Rain Lights ? REQUIREMENTS Vehicle must have rain light sensor installed. Light switch must be on 'AUTO' position.
Rain lights	Rain lights improve visibility while driving in rain or snow. ⚙ Fonctions Turn ON or OFF Rain Lights ? REQUIREMENTS Vehicle must have rain light sensor installed. Light switch must be on 'AUTO' position.
Rain lights	Rain lights improve visibility while driving in rain or snow. ⚙ Fonctions Turn ON or OFF Rain Lights ? REQUIREMENTS Vehicle must have rain light sensor installed. Light switch must be on 'AUTO' position.
Rain lights	Rain lights improve visibility while driving in rain or snow. ⚙ Fonctions Turn ON or OFF Rain Lights ? REQUIREMENTS Vehicle must have rain light sensor installed. Light switch must be on 'AUTO' position.